Roofing Contractor Deale Maryland
Let us save you the headache of trying to find a reliable roofing company and qualified contractor to help you with your needs. We have seen it all and we are ready to help you get your structure back in shape. Repairs, Installations, or full replacements, our contractors are waiting for your call.
Don’t wait until a small leak turns into a large one that damages interior walls and ceilings to take action. Calling a contractor now can save you a lot of money, time, and headache in the long run.
- Roof Repair and Replacement
- Roof Installation
- Commercial Roofing with TPO Membranes
- Flat Roofs for Commercial Buildings
- Asphalt Shingles
- Leaky Chimney Repair
- Ceiling Water Damage Restoration
With over 25 years of experience in the industry and the highest company warranty available from any contractor you can rest assured that your home or business is “covered” by the best roof in the industry!
Two Brothers Roofing in Deale is also experienced in new installation. Are you constructing a new home or business? We specialize in roofs and can have your home or business protected right.
Our Average Contact Form Response Time is 15 Minutes. We Invite You To Fill Out The Form Below
Roof Repair and Replacement Deale Maryland
Sometimes all we need to find is a reliable roofing company to assist us with minor repairs. We have been helping families save money for years by scheduling yearly roofing maintenance. The more diligent our contractors are in keeping up with your roof, the longer it will last. That is where we come in – Call our company with any questions you have or to schedule your repairs in Deale Maryland today!
How Do You Know There’s A Problem?
It can be hard to know there’s even a problem up there. After all, no one is that tall. But there are signs of a roof that needs repaired you can see from the ground and from inside the house.
Here are some signs that it might be time to call Two Brothers Roofing in Deale Maryland to come take a closer look:
- Singles that are curled, cracked, or absent – these are all indicators of the age of your roof. If you see any of these or you have shingles completely missing it’s time to get your roof replaced.
- Shingles that are dark, dirty, or wet – Shingles are supposed to repel moisture and let rain and dampness run off of your roof. If your shingles are wet then they’re retaining moisture and putting the underlying structures at risk. Keep in mind that if shingles are wet, dark, or dirty, the area might be bigger than you think since water rolls downhill.
- Lots of shingle granules in the gutters around your roof (you do have these right?). – These granules start to wear away from the shingles as they get old. When you start to see what looks like black sand in your gutters, it’s time for your roof to get some attention
- Blistering or peeling exterior paint – this is a good indicator that your roof or your gutter system isn’t doing it’s job
- Interior ceilings or wall staining – Water stains on walls or ceilings are the result of many different things. One of which is your roof failing and the underlayment is allowing moisture to get into the interior of your home’s walls and ceilings. Calling Two Brother’s Roofing will take care of this problem.
- Leaks in the attic after a storm – Sometimes leaks getting into the attic is due to flashing but sometimes it’s due to underlayment. If it’s the latter, you’ll need a roof replacement
These are just some of the signs. For a more in depth evaluation, don’t hesitate to call in a professional!
Replacing a roof can be a big investment, but we are proud to say that our prices are competitive and the work we do is always thorough. We promise no headaches to our customers because we will do the job correctly the first time around. You will see the friendliness of our team and how hard we work to provide 100% customer satisfaction, with the end result being a beautiful new roof that will last you for many years to come!
Many people feel that they can skip the professional installation and do it themselves. While this is certainly do-able, there are several things that you need to ask yourself first.
Are you afraid of heights? This goes without saying. If you’re working on a roof you need to be able to be up there working in the elements (and not afraid of heights) pretty comfortably. Your safety depends on your comfort level with being on the roof and how you prepare to be in the weather.
Are you pretty fit? That may sound slightly rude, but again, roofing isn’t an easy job physically. It involves climbing a ladder multiple times with heavy roofing shingles. Your body has to be able to handle the extra workload.
It’s much easier on homeowners to call a contractor to come get the job done! It can be cheaper to do it yourself in the short term but if you’ve never done it before you could either injure yourself or make a mistake that will cost you a lot of money in the long run.
Even if you’re experienced, roofing isn’t the most fun to do for the average person. However, it is fun for us! We would be happy to assist you in getting your roof installed with no extra stress on you!
Roof Installation Steps
Remove Old Shingles (if there is any)
Old roofing will probably need to be removed if there is any. If this is a new construction, this won’t be a problem. Many people feel that they can install a new roof over the old shingles to provide extra protection. This actually does the opposite. If the old roof isn’t stripped down to the sheathing it can cause premature failure of the new roof.
After the old one is removed, our company will look at what’s underneath to see if anything needs done before preparing to install the new roof. We look for any moist areas or trouble spots in the sheathing that need to be addressed or replaced.
Protect Against Ice
Being in Maryland, our customers are in an area that gets ice and snow during the winter months. It’s important for us to install an ice and water barrier around the roof. It’s sticky and adheres to the roof sheathing and then is nailed down for added strength and stability.
Put on the Drip Edge
This goes down in two different parts of the roof installation. For the lower part of the roof it goes down before the underlayment and for the sides it goes down after the underlayment.
Roof Underlayment Installation
After the first part of the Drip Edge is installed, the underlayment goes down. The underlayment comes in two thicknesses and it’s made up of materials that are water resistant.
After the underlayment is installed, it’s time to install your materials.
We understand how important it is to get this process done right. Our contractors don’t skimp or skip steps in order to save time and/or money. We get the job done right the first time so that your property has the best protection that it can have against the elements.
Call us today and schedule a time to complete your free estimate!
Anne Arundel County
- Linthicum heights
- Glen burnie
- Fort Meade
- Edge water
- Shady side
Commercial Roofing with TPO Membranes
TPO (Thermoplastic Polyolefin) is a single-ply reflective roofing membrane made of polypropylene and ethylene-propylene rubber. It’s usually installed so that the white membrane is exposed throughout the life of the roof.
There are several advantages to TPO roofing:
ENERGY EFFICIENT: TPO membranes are highly energy efficient. The white reflective surface of the membrane goes way past EPA’s ENERGY STAR requirements (we love that!). This means that your energy costs will be reduced because the interior of your facility will be kept comfortable on especially hot summer days.
EASY INSTALLATION: TPO membranes are lightweight and are manufactured with wider sheets. The material is easier to install and doesn’t have as many seams to seal. This helps you save on installation because it takes less time to install and doesn’t require as much labor cost.
DURABLE: TPO is resistant to mold, dirt, tears, and punctures. Also, because of the strength of TPO it can handle a building’s regular expansion and contraction more effectively than single-ply roofing products.
Two Brothers Roofing technicians are trained and qualified to install TPO roofing in Deale Maryland. If you think this type of roofing is best for your building, give us a call!
Flat Roofs for Commercial Buildings
The main point of a roof, whether flat or sloped, is to maintain the watertight integrity of a building and keep the underlying structures dry. This used to be a simple process. Now, today’s variety of flat or low slope roofing options has grown and is no longer simple.
Why have a flat roof?
That’s a great question! Flat roofs are absolutely everywhere. Factories, department stores, apartment buildings, large public structures, warehouses, and schools, all usually have pretty flat roofs. A flat roof’s design is both efficient and economical.
Part of the reason why flat roofs are so popular with commercial facilities is that they’re very cost efficient. Budget is usually a concern for many companies because businesses are large and have a decent area to cover.
Flat commercial roofs are cheaper to install because they require fewer materials. Extra framing costs are usually involved when you start adding peaks and valleys in the design.
Just like with residential structures, commercial roofs still require a drainage system. With how large commercial facilities are, this can increase the cost but overall, its cheaper and ends up saving companies money over the course of the installation.
We refer to these roofs as flat but usually there is a 2% slope to allow rainwater and snow to drain off. If water is allowed to sit on top, it can add weight and potentially cause damage.
Another reason why “flat” roofs are so popular is that they’re very practical for designing and constructing a commercial roof. They’re much easier for contractors to install on large buildings. Also if you installed a sloped roof it would either have to be very tall or have multiple peaks and valleys.
Retail and industrial companies must maximize their square footage so it wouldn’t make much sense to invest in sloped roofing. That money is best used elsewhere.
Space For Equipment
With commercial roofs, there is a need to put equipment on that isn’t required with residential structures. Usually things like air conditioners and other heating and cooling equipment needs to be up there. Mounting this equipment at ground level usually isn’t allowed by code and can pose a number of safety and security problems.
Machinery can often be tucked away in basements or other storage areas but on the ground they take up a lot of room and cause safety and comfort issues.
Flat roofs are an excellent solution. They provide a large, flat area that’s completely out of the way of commercial traffic. People and equipment are safe and they’re easily accessible for repairs and/or maintenance. The only risk is that it leaves the machinery open to the elements.
Do you have a commercial facility in Deale Maryland and looking for roof repair or installation? Two Brothers Roofing has the skills to get the job done. The length of time that your roof lasts very much depends on who and how it was installed. Our technicians are trained right from day one. We’re here to assist you!
Asphalt shingles are one of the least expensive roofing materials. They also come in a wide variety of colors. It’s very popular for use in homes and smaller residential projects because not only is it not very expensive, the installation process is simple because the singles are flexible. These shingles are also available in different textures and thickness and they can be treated against mold and mildew.
Asphalt shingles come in two categories. Both organic and fiberglass.
Organic shingles are made up of paper. They have an asphalt coating that give them their waterproof properties.
Fiberglass shingles are better for fire protection. They are also treated with a protective resin coating that gives them their waterproof properties.
Pros of asphalt shingles:
- Easy installation
- Last a long time
- Can be recycled
Cons of asphalt shingles:
- Sudden weather changes can cause decay
- Wind can cause uplift
- Maintenance is required
- Not environmentally friendly (even organic ones)
Leaky Chimney Repair
If you’re having problems with a leaking chimney in Deale Maryland call now to talk to a contractor.
There are several reasons why your chimney would leak:
Water Coming In Directly From the Top From Rain or Snow
Chimneys without covers get a lot of rain falling down into them. A chimney cover not only keeps the rain out, but it keeps birds, animals, and other debris that can cause issue out also.
Cracks in the Chimney Crown
The crown is the cement part on the top of the chimney. The bricks go around the flute lines but is open at the top. You need something to stop the rain, snow, and other moisture from falling in around the tiles. The very purpose of the chimney crown is to keep the rain out but if it’s cracked, moisture can seep in through them.
Leaking From the Inside Out from Condensation
In some older houses, the chimney isn’t installed and properly fitted with a properly sized liner, if at all.
Chimney flashing is what keeps the water from going into the place where the brick structure comes through the roof. If the gap between the bricks and the roof isn’t properly sealed up, water will pour right through there and cause leaks.
Leaks are never fun. Call Two Brothers Roofing Contractors for an evaluation and an estimate! We will never charge you for more than you need. You can trust your roof and chimney repairs with us.
How to Stop Leaks with Temporary Tarping and Tar Patches
Discovering you have a roof leak is never fun, especially when water is actually leaking into your home. If your roof begins to leak during a holiday weekend or during some other time when you can’t get assistance right away, sometimes a temporary roof repair is needed.
One of the quickest and least expensive ways you can temporarily fix a leak is to cover the affected area with plastic tarp. Make sure that you get one that can be used outdoors and is big enough to cover the entire affected area.
Once you get the tarp in the area, wrap it tightly down onto the roof, smooth it out, and nail down the edges. Make sure you cover the nail heads with roofing cement so that water doesn’t seep into the holes.
If you don’t have access to tarp but have roofing tar on hand, you can use tar to patch a leak but it’s not ideal. Even though it is roofing tar, after all, and it can be applied when the roof itself is web, it can cause more problems than it actually solves.
If you absolutely have to use tar, be aware that it’s just a temporary fix. Over a fairly short period of time, the tar on the roof is going to begin to dry and crack. In those cracks, the same leak that you tried to patch will be once again exposed.
While you may have been able to replace a broken shingle or piece of chimney lead easily before, now you have to remove the tar and the damaged shingles before a professional can repair the roof properly.
Having your roof repaired the first time can save you a lot of time and money in the long run. Give Two Brothers Roofing a call to take care of your roof leaks!
Water Damage Restoration To Your Ceiling
Water, as life giving as it is, can definitely be destructive. When it gets into the drywall that’s on your walls and ceilings not only can it be unsightly but it can weaken the structure enough that it collapses and falls apart. I’m sure you know this can cause huge homeowner headaches.
No need to panic, ceilings can be repaired and their strength and aesthetics restored.
There are several things that need to happen to repair a ceiling that has water marks and/or has weakened due to damage.
Step 1: Find the water leak.
If you haven’t found the water leak yet, it’s imperative that this happens first. This goes without saying but if you don’t take care of the source first you’ll just end up with the same problem.
Two Brothers Roofing has the tools and the skills to find a stop leaks fast!
Step 2: Remove water-damaged drywall
Before you start tearing this down, make sure that drop cloths are laid down in the area to protect flooring and furniture.
Remove all compromised drywall by hand or use a hammer or wrecking bar to remove it.
For safety, make sure you’re wearing goggles, especially when dealing with ceilings!
Step 3: Repair
If you’re using a patch for a small area, cut a replacement square from a piece of drywall to fit that’s 2” longer and 2” wider than the whole to be filled in. Damaged areas more than 12 square inches may need a complete replacement panel installed. Large pieces of drywall need to be anchored to ceiling joists.
Step 4: Prime and Paint
Apply Primer/Sealer with a large paintbrush or roller applicator. Cover the entire surface of the wall.
After priming, paint over the area.
Step 5: Clean Up
Use a shop vacuum to clean up dust and debris. Also pick up any drop cloths, remove painter’s tape, and clean any brushes or rollers.
Issues and leaks can definitely be enough to ruin your day. Reach out to Two Brothers Roofing for your roofing needs. No need to stress or worry about whether it’s done right. Our roofing jobs come with a guarantee!
Submit your review